Microsoft LPF-00004 Operator's Manual Page 105
- Page / 157
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
CyberControl SOFTWARE Page 87
C
YBER
A
MP
380, COPYRIGHT MARCH 2002, AXON INSTRUMENTS, INC.
9) OUTPUT AMPLIFICATION
PC: The Total Gain field displays the combination of the Initial Gain (pre-filter) along
with any post-filter amplification. A predefined list of values are allowed. The
setting can be typed in, or the spinner buttons can be used to scroll through the
values.
Macintosh: The OutAmp column displays the amount of post-filter amplification. Selecting a
field pops up a list of available output gain settings. The Total Amp column
displays the combination of the PreAmp pre-filter gain along with the OutAmp
post-filter gain.
Keyboard Commands
PC: When a field is highlighted, the Up and Down arrow keys can be used to scroll through the
values, as if clicking on the spinner buttons. For the Positive Input and Negative Input
fields, the <Page Up> and <Page Down> keys can also be used to jump to the beginning or
end of the lists.
Macintosh: When the main window is active, pressing any of the four arrow keys will move the cursor
through the fields in the spreadsheet. When a field is selected, its value can be changed
with the <pg up>and <pg dn> keys, and x10 with the <shift+pg up> and <shift+pg dn>
keys. In the pop-up columns, the value is always changed to the next item in the list of
available values. In the Offset Column, the value is changed according to the values entered
in the Offset Units… Dialog Box; by default these values are 1 mV and -1 mV.
Pressing the Help key will open a Help window. Double-clicking on a column name will
display appropriate information in the Help window.
Overload Handling
PC: Automatic polling for overload conditions is set in the File Options dialog. When an
overload condition is detected on a CyberAmp channel, the channel # tab is highlighted in
red. Reduce the gain to avoid an overload condition
Macintosh: CyberControl constantly scans the overload status of the CyberAmp channels. If an
overload is detected on any channel, the window icon is inverted and highlighted in red; if
the window is not iconized, a red ball is placed next to the overloaded channel. Reduce the
amplification to avoid an overload condition.
- CyberAmp 380 1
- Declaration of Conformity 3
- IMPORTANT INFORMATION 5
- RENSEIGNMENTS IMPORTANTS 6
- WICHTIGE INFORMATIONEN 7
- INFORMACION IMPORTANTE 8
- Explanation of symbols 9
- Explication des symboles 9
- Explicación de símbolos 9
- SÉCURITÉ 10
- SICHERHEITS 10
- HINWEISE 10
- SEGURIDAD 10
- COPYRIGHT 11
- VERIFICATION 11
- TABLE OF CONTENTS 13
- INTRODUCTION 19
- Page 2 INTRODUCTION 20
- INTRODUCTION Page 3 21
- FUNCTIONAL DESCRIPTION 23
- General Features 26
- FUNCTIONAL CHECKOUT 29
- TYPICAL CONFIGURATIONS 33
- Supply Voltage 37
- Changing the Fuse 37
- Grounding and Hum 38
- Power-Supply Glitches 39
- Input Coupling 39
- Expansion 40
- Low-Pass Filter 41
- Amplitude Characteristics 42
- Sampling Rate 43
- 10-90% Rise Time 43
- AC Coupling and Autozeroing 44
- 3 dB frequency of 44
- Time Constant 46
- 100 1.6 46
- Saturation 47
- Notch Filter 48
- Overload Detection 49
- Audio Monitor 50
- External Input 51
- Electrode Test 52
- Strain Gauges 55
- Active Probes 56
- Common-Mode Rejection Ratio 57
- Troubleshooting 59
- TRANSDUCERS 61
- Page 44 TRANSDUCERS 62
- TRANSDUCERS Page 45 63
- EMG, EEG, ECG Recording 64
- Nerve Cuffs 65
- Metal Microelectrodes 65
- Page 48 TRANSDUCERS 66
- Pressure 67
- Acceleration 67
- Self Heating 68
- Isolation 68
- Insulation Techniques 68
- AI 400 SERIES SmartProbes 69
- Transducer Adapter 71
- Input Connector Color Scheme 72
- Recommended Input Coupling 73
- Connector 74
- Example Circuits 75
- Basic Thermistor Circuit 76
- Amplifier Probes 78
- Current Probes 79
- Photodiode Amplifier 79
- Linear Potentiometers 80
- Rotary Potentiometers 80
- Panel Switch 81
- Foot Switch 81
- CMD300 CONTROL SOFTWARE 83
- Command-Line Mode 85
- Interactive Mode 85
- Command-File Mode 86
- Command Reference 87
- CMD300 OVERLOAD 91
- CMD300 REPEAT OVERLOAD 94
- QUICK300 CONTROL SOFTWARE 97
- Command Line Options 100
- CyberControl SOFTWARE 101
- Starting CyberControl 102
- Overload Handling 105
- Keyboard Commands 105
- Communications Settings 107
- PC Menus 108
- Macintosh Menus 109
- PROGRAMMER'S GUIDE 112
- Libraries and Example Code 114
- > end of response 116
- AT3F5 24000 118
- 2 4 6 8 10 ... 28000 30000 118
- AT8R06000 121
- D5=-1234500 124
- Implementation Notes 125
- Support Routine Details 125
- Example Programs 129
- SPECIFICATIONS 135
- Page 118 SPECIFICATIONS 136
- Offset range: ±10 V 137
- Page 120 SPECIFICATIONS 138
- SPECIFICATIONS Page 121 139
- Page 122 SPECIFICATIONS 140
- REFERENCES 141
- ADJUSTMENT PROCEDURES 143
- Other Adjustments 144
- CIRCUIT DIAGRAMS Page 127 145
- SERIAL COMMUNICATIONS CABLES 147
- LIST OF FIGURES AND TABLES 149
- WARRANTY 151
- WARNING 153
- INDEX Page 137 155
Related products and manuals for Measuring, testing & control Microsoft LPF-00004
(82 pages)Oreck XL2000RHZ manuels
Manuels d'utilisation et guides de l'utilisateur pour Aspirateurs Oreck XL2000RHZ.
Nous fournissons des manuels en pdf 1 Oreck XL2000RHZ à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comments to this Manuals